VOLVO
ECM-P058000 - Cruise Control Multi-Function Input A Circuit Low. General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
5 modeliS60 (2011–), S80 (2007–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Pokaż modele wg rocznika i silnika (13)
- Volvo S60 (2011–)2011–2012Tylko silnik: B5254T5
- Volvo S80 (2007–)2007–2008Tylko silnik: B5254T6
- Volvo S80 (2007–)2009Tylko silnik: B5254T6, B5254T8, D5244T10
- Volvo S80 (2007–)2010Tylko silnik: B5254T10, B5254T11, B5254T8, D5244T10, D5244T14, D5244T19
- Volvo S80 (2007–)2011Tylko silnik: B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2012Tylko silnik: B5254T10
- Volvo V70 (2008–)2008Tylko silnik: B5254T6
- Volvo V70 (2008–)2009Tylko silnik: B5254T6, B5254T8, D5244T10
- Volvo V70 (2008–)2010Tylko silnik: B5254T10, B5254T11, D5244T10, D5244T14, D5244T19
- Volvo V70 (2008–)2011Tylko silnik: B5254T10, B5254T11
- Volvo V70 (2008–)2012Tylko silnik: B5254T10
- Volvo XC60 (2009–)2010Tylko silnik: D5244T10, D5244T14, D5244T16
- Volvo XC70 (2008–)2010Tylko silnik: D5244T10, D5244T14, D5244T16
Co oznacza ten kod błędu?
The ECM reads the cruise control input from the front monitoring module (FSM) over the CAN network. The code concerns a low signal from the FSM and is checked when the ignition is on. It can also be set by a CAN fault or a fault in the steering wheel module, the central electronics module, the brake control module or the transmission control module.
Możliwe przyczyny
- Open circuit, short circuit or temporary interference on the CAN wires
- Internal fault in the ECM itself
- Internal fault in another control module on the same part of the CAN network, or a fault in the front monitoring module (FSM)
- Contact resistance, oxidation or open circuit in connections
- The ECM is not intended for this car, for example a used module with different software or hardware
Co możesz zrobić
- 1Check that the fuses are intact
- 2Read out and deal with the fault codes in the central electronics module (CEM) and other affected modules first. Clear this code only once they have been dealt with
- 3Check that the connectors on the CAN network are firmly seated and not corroded
- 4Use a multimeter to check that the CAN wires have no open circuit and are not shorted to ground or supply voltage
- 5If nothing is found, have a workshop look for the fault in the front monitoring module (FSM) and check that the correct engine control module is fitted for this car
Objawy, które możesz zauważyć2
- Cruise control does not work at all
- Cruise control does not engage
Na co może wpływać usterka2
- Cruise control is switched off
- Cruise control cannot be activated
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.