VOLVO
ECM-P068611 - ECM/PCM Power Relay Control Circuit Low. General Electrical Failures. Circuit short to ground
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
When the ignition goes off, the system relay releases only after a set delay, which gives the control module time to finish what it is doing before power to the affected parts is removed. The code is set when the relay releases too late or too early compared with what is expected.
Możliwe przyczyny
- Signal wire short-circuited to ground
- No supply voltage to the system relay
- Damaged system relay
Co możesz zrobić
- 1Read and clear the fault code, and check the battery charge and that the terminals are secure
- 2Check the fuses for the system relay supply in the owner's manual
- 3Look at the wiring to the system relay for chafing, pinch damage and loose contacts, especially where it may have touched the body
- 4Use a multimeter to check that the signal wire to the system relay has no contact with ground (the body), with the connectors disconnected
- 5Check that supply voltage reaches the relay: measure at the connector with the ignition on
- 6If the fault remains after these checks, have a workshop check the system relay
Objawy, które możesz zauważyć2
- The battery may appear weak
- The vehicle electrical system may have lower voltage than normal
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.