VOLVO
ECM-P069900 - Sensor Reference Voltage C Circuit High. General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
9 modeliC30 (2007–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–)
Pokaż modele wg rocznika i silnika (18)
- Volvo C30 (2007–2013)2011–2013Tylko silnik: D4162T
- Volvo S40 (2004–2013)2011–2012Tylko silnik: D4162T
- Volvo S60 (2011–)2011–2012Tylko silnik: B5254T5, D4162T
- Volvo S60 (2011–)2013–2015Tylko silnik: D4162T
- Volvo S80 (2007–)2007–2008Tylko silnik: B5254T6
- Volvo S80 (2007–)2009Tylko silnik: B5254T6, B5254T8
- Volvo S80 (2007–)2010–2011Tylko silnik: B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2012Tylko silnik: B5254T10, D4162T
- Volvo S80 (2007–)2013–2015Tylko silnik: D4162T
- Volvo V40 (2013–)2013–2015Tylko silnik: D4162T
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: D4162T
- Volvo V50 (2004–2013)2011–2012Tylko silnik: D4162T
- Volvo V60 (2011–)2011–2015Tylko silnik: D4162T
- Volvo V70 (2008–)2008Tylko silnik: B5254T6
- Volvo V70 (2008–)2009Tylko silnik: B5254T6, B5254T8
- Volvo V70 (2008–)2010–2011Tylko silnik: B5254T10, B5254T11
- Volvo V70 (2008–)2012Tylko silnik: B5254T10, D4162T
- Volvo V70 (2008–)2013–2015Tylko silnik: D4162T
Co oznacza ten kod błędu?
The control module has found a voltage that is too high in the supply to the sensors. This may be due to a wire to the sensors being short-circuited, a damaged sensor, a damaged control module, a fault in the charging system or a damaged battery. The code is general and does not say what type of fault it is.
Możliwe przyczyny
- Voltage wire to the sensor short-circuited to ground
- Voltage wire to the sensor short-circuited to voltage
- Damaged sensor
- Sensor wiring shorted to ground or to voltage
- Fault in the charging system
- Damaged battery
Co możesz zrobić
- 1Read and clear the fault code, and test-drive to see whether it returns
- 2Check that the battery is charged and that the terminals are secure
- 3Look at the wiring to the sensors for chafing and pinch damage, and at the connectors for oxidation
- 4Use a multimeter to check that the wiring to the sensors has no contact with voltage, with the connectors disconnected
- 5Also check that the wiring has no contact with ground (the body), with the connectors disconnected
- 6If the fault remains, have a workshop check the charging system and the sensors. If the fault is permanent the control module may need replacing, which a workshop does
Objawy, które możesz zauważyć4
- Deterioration in vehicle performance
- Engine misfires
- Engine is difficult to start
- Warning symbol and text message in the display
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.