VOLVO
ECM-P086E00 - Neutral Position Sensor "A" Circuit Intermittent/Erratic. General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
11 modeliC30 (2007–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Pokaż modele wg rocznika i silnika (29)
- Volvo C30 (2007–2013)2011–2013Tylko silnik: D4162T
- Volvo S40 (2004–2013)2011–2012Tylko silnik: D4162T
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, D4162T
- Volvo S60 (2011–)2012Wszystkie silniki oprócz: B4204T7, B5254T5, B6304T4
- Volvo S60 (2011–)2013–2014Wszystkie silniki oprócz: B4204T7, B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2015Wszystkie silniki oprócz: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2011Tylko silnik: B4164T
- Volvo S80 (2007–)2012Tylko silnik: B4164T, B4164T2, D4162T, D5204T3, D5244T11, D5244T15
- Volvo S80 (2007–)2013Tylko silnik: B4164T, B4164T2, D4162T, D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S80 (2007–)2014Wszystkie silniki oprócz: B4204T6, B4204T7, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2015Wszystkie silniki oprócz: B6304T4, B6324S4, B6324S5
- Volvo V40 (2013–)2013–2014Wszystkie silniki oprócz: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Wszystkie silniki oprócz: B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2014Tylko silnik: B4164T, D4162T, D5204T4, D5204T6
- Volvo V40 Cross Country (2013–)2015Wszystkie silniki oprócz: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V50 (2004–2013)2011–2012Tylko silnik: D4162T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, D4162T
- Volvo V60 (2011–)2012Wszystkie silniki oprócz: B4204T7, B6304T4
- Volvo V60 (2011–)2013Wszystkie silniki oprócz: B4204T7, B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Wszystkie silniki oprócz: B4204T7, B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Wszystkie silniki oprócz: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V70 (2008–)2011Tylko silnik: B4164T
- Volvo V70 (2008–)2012Wszystkie silniki oprócz: B4204T7, B5254T10, B6304T4, B6324S5
- Volvo V70 (2008–)2013–2014Wszystkie silniki oprócz: B4204T7, B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2015Wszystkie silniki oprócz: B5204T9, B6304T4
- Volvo XC60 (2009–)2012Tylko silnik: D5204T3, D5244T11, D5244T15, D5244T17
- Volvo XC60 (2009–)2013–2014Wszystkie silniki oprócz: B4204T7, B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Wszystkie silniki oprócz: B4204T7, B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2012–2015Wszystkie silniki oprócz: B6304T4, B6324S4, B6324S5
Co oznacza ten kod błędu?
The engine control module adapts to the gear lever positions while driving, using the voltage levels that the neutral position sensor gives for high and low gear. The code is set when these levels vary too much for the adaptation to be carried out. It therefore indicates that the sensor signal is uneven or erratic.
Możliwe przyczyny
- Neutral position sensor adaptation not reset after work on the gearbox
- Loose contact or oxidation in the connector
- Short circuit or break in the wiring to the sensor
- Sensor incorrectly fitted to the gearbox
- Damaged link arm that the sensor is attached to
- Damaged neutral position sensor
Co możesz zrobić
- 1Has any work recently been done on the gearbox? If so, the adaptation may need resetting, which is a job for a workshop
- 2Check that the fuses are intact. The locations are shown in the instruction manual or on the fuse list
- 3Check that the connector at the neutral position sensor is firmly seated and free from looseness and oxidation
- 4Check that the link arm and sensor are firmly fixed and undamaged
- 5Use a multimeter to check that the signal wire to the sensor has no break and is not shorted to earth
- 6If you have a diagnostic tool, check in live data that the sensor value changes smoothly as the gear lever is moved, with no jumps between positions
Objawy, które możesz zauważyć3
- Automatic engine stop-start does not work while driving
- Automatic engine stop-start does not work at idle
- Starting and auto-start do not work
Na co może wpływać usterka1
- The automatic engine stop-start function is switched off
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.