VOLVO
ECM-P08A800 - Clutch Pedal Position Sensor Circuit Range/Performance. General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
8 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Pokaż modele wg rocznika i silnika (30)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, D4162T
- Volvo S60 (2011–)2012Wszystkie silniki oprócz: B4204T7, B5254T5, B6304T4
- Volvo S60 (2011–)2013Wszystkie silniki oprócz: B4204T7, B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2014Tylko silnik: B4164T, B4164T2, B4164T3, D4162T, D4204T5, D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3, D4162T, D4204T5, D5204T3, D5204T7, D5244T11, D5244T15, D5244T23
- Volvo S80 (2007–)2011Tylko silnik: B4164T
- Volvo S80 (2007–)2012Tylko silnik: B4164T, B4164T2, D4162T, D5204T3, D5244T11, D5244T15
- Volvo S80 (2007–)2013Tylko silnik: B4164T, B4164T2, D4162T, D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S80 (2007–)2014Tylko silnik: B4164T, B4164T2, D4162T, D4204T5, D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S80 (2007–)2015Tylko silnik: B4164T, D4162T, D4204T5, D5204T3, D5244T15
- Volvo V40 (2013–)2013–2014Wszystkie silniki oprócz: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Wszystkie silniki oprócz: B4204T11, B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2014Tylko silnik: B4164T, D4162T, D5204T4, D5204T6
- Volvo V40 Cross Country (2013–)2015Tylko silnik: B4164T, D4162T, D4204T14, D5204T6
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, D4162T
- Volvo V60 (2011–)2012Wszystkie silniki oprócz: B4204T7, B6304T4
- Volvo V60 (2011–)2013Wszystkie silniki oprócz: B4204T7, B5204T8, B5204T9, B6304T4, D82PHEV
- Volvo V60 (2011–)2014Wszystkie silniki oprócz: B4204T11, B4204T12, B4204T15, B4204T7, B4204T9, B5204T8, B5204T9, B5254T12, B6304T4, D82PHEV
- Volvo V60 (2011–)2015Wszystkie silniki oprócz: B4204T11, B4204T12, B4204T15, B4204T9, B5204T9, B5254T12, B6304T3, B6304T4, B6304T5, D82PHEV, D87PHEV
- Volvo V70 (2008–)2011Tylko silnik: B4164T
- Volvo V70 (2008–)2012Wszystkie silniki oprócz: B4204T7, B5254T10, B6304T4, B6324S5
- Volvo V70 (2008–)2013Wszystkie silniki oprócz: B4204T7, B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2014Wszystkie silniki oprócz: B4204T11, B4204T7, B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2015Wszystkie silniki oprócz: B4204T11, B5204T9, B6304T4
- Volvo XC60 (2009–)2012Tylko silnik: D5204T3, D5244T11, D5244T15, D5244T17
- Volvo XC60 (2009–)2013Wszystkie silniki oprócz: B4204T7, B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2014Tylko silnik: D4204T5, D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17
- Volvo XC60 (2009–)2015Tylko silnik: D4204T5, D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17, D5244T23
- Volvo XC70 (2008–)2012–2013Wszystkie silniki oprócz: B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2014–2015Wszystkie silniki oprócz: B4204T11, B6304T4, B6324S4, B6324S5
Co oznacza ten kod błędu?
The engine control module (ECM) checks the position sensor against the clutch pedal switch. The code indicates that the sensor signal is wrong, because the pedal position does not agree with the switch on some drives. If the driver's use of the clutch explains the fault, no repair is needed.
Możliwe przyczyny
- Contact resistance, oxidation or loose contact in the connector
- Damaged signal wire
- Damaged clutch pedal sensor, position sensor or pedal switch
- Many gear changes made without pressing the clutch pedal far enough
- Long driving with the clutch pedal held down
Co możesz zrobić
- 1If the driver's use of the clutch explains the fault, no repair is needed
- 2Check that the fuses are intact. The locations are shown in the instruction manual or on the fuse list
- 3Check that the connectors at the position sensor and pedal switch are firmly seated and free from oxidation and contact resistance
- 4Check that the clutch pedal moves freely and does not stick, and that the sensors are firmly fixed
- 5Use a multimeter to check that the signal wire from the sensor has no break and no contact with earth (the body)
- 6Have a workshop check that the engine control module has the latest software, as an improved version copes better with harder clutch use
Objawy, które możesz zauważyć5
- Starting and auto-start do not work
- Automatic engine stop-start does not work, both at idle and while driving
- The car may hesitate, surge or run jerkily while driving, even at constant speed
- A message and a warning symbol are shown in the display
- The check engine lamp lights or behaves abnormally
Na co może wpływać usterka1
- The automatic engine stop-start function is switched off
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.