VOLVO
ECM-P08A900 - Clutch Pedal Position Sensor Circuit Low. General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
8 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Pokaż modele wg rocznika i silnika (28)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3
- Volvo S60 (2011–)2012Tylko silnik: B4164T2, D5204T3, D5244T11, D5244T15
- Volvo S60 (2011–)2013Tylko silnik: B4164T, B4164T2, B4164T3, D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S60 (2011–)2014Wszystkie silniki oprócz: B4204T7, B5204T8, B5204T9, B5254T12, B5254T14, B6304T4, D4162T
- Volvo S60 (2011–)2015Wszystkie silniki oprócz: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5, D4162T
- Volvo S80 (2007–)2011Tylko silnik: B4164T
- Volvo S80 (2007–)2012Tylko silnik: B4164T2, D5204T3, D5244T11, D5244T15
- Volvo S80 (2007–)2013Tylko silnik: B4164T, B4164T2, D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S80 (2007–)2014Wszystkie silniki oprócz: B4204T6, B4204T7, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5, D4162T
- Volvo S80 (2007–)2015Wszystkie silniki oprócz: B6304T4, B6324S4, B6324S5, D4162T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3, D5204T4, D5204T6
- Volvo V40 (2013–)2014Tylko silnik: B4164T, B4164T3, B4164T4, D5204T4, D5204T6
- Volvo V40 (2013–)2015Wszystkie silniki oprócz: B5204T8, B5204T9, D4162T
- Volvo V40 Cross Country (2013–)2013–2014Tylko silnik: B4164T, D5204T4, D5204T6
- Volvo V40 Cross Country (2013–)2015Tylko silnik: B4164T, B4204T11, D4204T14, D5204T6
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3
- Volvo V60 (2011–)2012Tylko silnik: B4164T2, D5204T3, D5244T11, D5244T15
- Volvo V60 (2011–)2013Wszystkie silniki oprócz: B4204T7, B5204T8, B5204T9, B6304T4, D4162T, D82PHEV
- Volvo V60 (2011–)2014Wszystkie silniki oprócz: B4204T7, B5204T8, B5204T9, B5254T12, B6304T4, D4162T, D82PHEV
- Volvo V60 (2011–)2015Wszystkie silniki oprócz: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5, D4162T, D82PHEV, D87PHEV
- Volvo V70 (2008–)2011Tylko silnik: B4164T
- Volvo V70 (2008–)2012Tylko silnik: B4164T2, D5204T3, D5244T11, D5244T15
- Volvo V70 (2008–)2013–2014Wszystkie silniki oprócz: B4204T7, B5204T9, B6304T4, B6324S5, D4162T
- Volvo V70 (2008–)2015Wszystkie silniki oprócz: B5204T9, B6304T4, D4162T
- Volvo XC60 (2009–)2012Tylko silnik: D5204T3, D5244T11, D5244T15, D5244T17
- Volvo XC60 (2009–)2013–2014Wszystkie silniki oprócz: B4204T7, B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Wszystkie silniki oprócz: B4204T7, B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2012–2015Wszystkie silniki oprócz: B6304T4, B6324S4, B6324S5
Co oznacza ten kod błędu?
The signal from the clutch pedal position sensor, sent over CAN from the central electronic module (CEM), lies below the permitted value for the pedal position. The engine control module checks that the signal is reasonable, including against the pedal switch. The code is set during driving when the signal stays too low for too long.
Możliwe przyczyny
- Contact resistance, oxidation or loose contact in the connector
- Damaged signal wire, or a break in it
- Signal wire shorted to earth
- Damaged clutch pedal position sensor
- Damaged clutch pedal sensor
- The root cause is in the central electronic module (CEM)
Co możesz zrobić
- 1Read the engine control module fault codes. If any of ECM-U012088, ECM-U000188, ECM-U1A1400, ECM-U000108 or ECM-U000100 is stored, investigate it first
- 2If ECM-U010482, ECM-P193582, ECM-P080582 or ECM-U042600 is stored, investigate it first
- 3Check that the fuses are intact. The locations are shown in the instruction manual or on the fuse list
- 4Use a multimeter to check that the wire from the sensor has no break and no contact with earth (the body)
- 5Check that the connectors at the position sensor are firmly seated and free from oxidation
- 6If the fault remains after these checks, have a workshop investigate the central electronic module (CEM), as the code points to a fault there
Objawy, które możesz zauważyć5
- Starting and auto-start do not work
- Cruise control cannot be engaged
- A message and a warning symbol are shown in the display
- Automatic engine stop-start does not work, both at idle and while driving
- The car may hesitate, surge or run jerkily while driving
Na co może wpływać usterka2
- The brake pedal must be depressed for auto-start
- The automatic engine stop-start function is switched off
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.