Przejdź do treści
    OBD Tuning
    WYŚLIJ DO NAS
    WYŚLIJ DO NAS
    Strona główna
    Kody błędów
    VOLVO
    ECM-P113700
    VOLVO

    ECM-P113700 - Lack Of HO2S12 Switches - Sensor Indicates Lean. General Failure Information. No sub type information

    Układ

    Sterownik silnika (ECM)

    Modele Volvo, których dotyczy ten kod błędu

    Dotyczy następujących modeli:

    4 modele

    S80 (2007–), V70 (2008–), XC70 (2008–), XC90 (2003–)

    Pokaż modele wg rocznika i silnika (9)
    • Volvo S80 (2007–)2007Tylko silnik: B6324S, B8444S
    • Volvo S80 (2007–)2008Tylko silnik: B4204S3, B4204S4, B6324S
    • Volvo S80 (2007–)2009–2011Tylko silnik: B4204S3, B4204S4
    • Volvo V70 (2008–)2008Tylko silnik: B4204S3, B4204S4, B6324S
    • Volvo V70 (2008–)2009–2011Tylko silnik: B4204S3, B4204S4
    • Volvo XC70 (2008–)2008Tylko silnik: B6324S
    • Volvo XC90 (2003–)2005–2006Tylko silnik: B8444S
    • Volvo XC90 (2003–)2007Tylko silnik: B6324S, B8444S
    • Volvo XC90 (2003–)2008Tylko silnik: B6324S

    Co oznacza ten kod błędu?

    The ECM continuously monitors the voltage of the rear oxygen sensor on bank 1, which is the cylinder row at the front with cylinders 1, 3, 5 and 7. The code is set when the voltage falls outside the range the ECM accepts, or when the sensor wrongly shows a lean mixture.

    Możliwe przyczyny

    • Contact resistance or oxidation in the connections
    • Signal wire shorted to ground
    • Broken signal wire
    • Damaged rear oxygen sensor on bank 1
    • Air leak in the intake pipe

    Co możesz zrobić

    1. 1If you have a diagnostic tool: start the engine, let it idle for a while, then read the fault status. Malfunction found means the fault is present now
    2. 2Do not use rust solvent spray or grease in the oxygen sensor connector, and check that it is firmly seated and free from oxidation
    3. 3Inspect the signal wire for chafing, and use a multimeter to check that it is unbroken and has no contact with ground
    4. 4Look for air leaks in the intake pipe, for example at hoses and connections
    5. 5If you find nothing above: try a new rear oxygen sensor, or have a workshop replace it

    Objawy, które możesz zauważyć1

    • Malfunction indicator (MIL) lamp is lit

    Na co może wpływać usterka1

    • Control of the rear oxygen sensor is switched off

    Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.

    OBD Tuning

    Wiodące centrum ekspertów Szwecji w elektronice motoryzacyjnej. Oferujemy profesjonalną optymalizację silnika, naprawę sterowników i diagnostykę z gwarancją 12 miesięcy.

    Usługi

    • Optymalizacja silnika
    • Naprawa sterownika
    • Klonowanie modułów
    • Zestaw wskaźników
    • SRS / Poduszka powietrzna
    • Immobilizer

    Baza danych & Diagnostyka

    • Baza danych sterowników
    • Katalog kodów DTC
    • Przewodniki diagnostyczne & Pomiary
    • Analizator błędów AI
    • Aktualności

    Producenci ECU

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    Firma

    • O nas
    • Kontakt
    • Partnerzy warsztatów
    • Przewodnik wysyłki
    • Gwarancja
    • FAQ
    • Regulamin
    • Polityka prywatności
    • Mapa strony

    • Optymalizacja silnika
    • Naprawa sterownika
    • Klonowanie modułów
    • Zestaw wskaźników
    • SRS / Poduszka powietrzna
    • Immobilizer

    • Baza danych sterowników
    • Katalog kodów DTC
    • Przewodniki diagnostyczne & Pomiary
    • Analizator błędów AI
    • Aktualności

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    • O nas
    • Kontakt
    • Partnerzy warsztatów
    • Przewodnik wysyłki
    • Gwarancja
    • FAQ
    • Regulamin
    • Polityka prywatności
    • Mapa strony

    Odwiedź nas

    Gjuterigatan 29, Karlstad

    Zadzwoń do nas

    054-830 480

    Napisz do nas

    service@obdtuning.se

    © 2026 OBD Tuning Karlstad. Wszelkie prawa zastrzeżone.