VOLVO
ECM-P129211 - Injector High Side Short To GND Or VBATT - Bank 2. General Electrical Failures. Circuit short to ground
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
This fault concerns the signal to the cylinder 3 injector, which is too low when the engine control module checks the circuit on the supply side. The engine needs to be running for the fault to be detected. The cause can be a signal wire shorted to earth, or a damaged injector.
Możliwe przyczyny
- The signal wire is short-circuited to earth
- Damaged injector
Co możesz zrobić
- 1Check that the fuses are intact. The locations are in the owner's manual or on the fuse box cover.
- 2Go through the connector to the cylinder 3 injector so that it is secure, clean and free from corrosion.
- 3Use a multimeter to check that the wire to the cylinder 3 injector is not shorted to earth (the body). Make the measurement with the ignition off.
- 4With a diagnostic tool you can activate the cylinder 3 injector. Listen for a click and compare with the other cylinders.
- 5If the fault returns, have a workshop with diagnostic equipment check the cylinder 3 injector and its wire.
Objawy, które możesz zauważyć4
- The Check engine (malfunction) lamp comes on or behaves abnormally
- Poor performance, the car lacks power
- The engine hesitates, surges or runs unevenly, at unclear times
- Unusual noise while driving
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.