VOLVO
ECM-P193484 - Vehicle Speed Signal. Bus Signal / Message Failures. Signal below allowable range
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
Although the code is named signal below allowable range, it applies when the engine control module (ECM) has registered that the speed value reported by the brake control module (BCM) is excessively high. The code is event controlled: it does not show a fault in the control module where it is active, but works mainly as information. It is only set when driving under certain conditions and disappears when those conditions no longer apply.
Możliwe przyczyny
- Faulty speed value from the brake control module (BCM), where the cause should be looked for
Co możesz zrobić
- 1Read off the codes in the brake control module (BCM) first and remedy them
- 2Investigate the speed signal while driving, as the code is only set under certain driving conditions
- 3If the code remains after the fault in the brake control module has been remedied, it can be cleared in the engine control module
- 4Check the connectors to the brake control module and its wiring for chafing and moisture
Objawy, które możesz zauważyć1
- No noticeable symptoms for the driver
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.