VOLVO
ECM-P212036 - Throttle/Pedal Position Sensor/Switch D Circuit. FM (Frequency Modulated) / PWM (Pulse Width Modulated) Failures. Signal frequency too low
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
12 modeliC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Pokaż modele wg rocznika i silnika (40)
- Volvo C30 (2007–2013)2011–2013Tylko silnik: D5204T, D5204T5
- Volvo C70 (2006–2013)2011Tylko silnik: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Wszystkie silniki oprócz: B5254T7
- Volvo S40 (2004–2013)2011–2012Tylko silnik: D5204T, D5204T5
- Volvo S60 (2011–)2011Tylko silnik: D5204T2, D5244T10
- Volvo S60 (2011–)2012Tylko silnik: D5204T3, D5244T11, D5244T15
- Volvo S60 (2011–)2013–2014Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S60 (2011–)2015Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T15, D5244T23
- Volvo S80 (2007–)2009Tylko silnik: D5244T10
- Volvo S80 (2007–)2010Tylko silnik: D5244T10, D5244T14, D5244T19
- Volvo S80 (2007–)2011Tylko silnik: D5204T2, D5244T10
- Volvo S80 (2007–)2012Tylko silnik: D5204T3, D5244T11, D5244T15
- Volvo S80 (2007–)2013–2014Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S80 (2007–)2015Tylko silnik: D5204T3, D5244T15
- Volvo V40 (2013–)2013–2014Tylko silnik: D5204T4, D5204T6
- Volvo V40 (2013–)2015Tylko silnik: D5204T6
- Volvo V40 Cross Country (2013–)2013–2014Tylko silnik: D5204T4, D5204T6
- Volvo V40 Cross Country (2013–)2015Tylko silnik: D5204T6
- Volvo V50 (2004–2013)2011–2012Tylko silnik: D5204T, D5204T5
- Volvo V60 (2011–)2011Tylko silnik: D5204T2, D5244T10
- Volvo V60 (2011–)2012Tylko silnik: D5204T3, D5244T11, D5244T15
- Volvo V60 (2011–)2013Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T15, D5244T17, D82PHEV
- Volvo V60 (2011–)2014Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17, D82PHEV
- Volvo V60 (2011–)2015Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17, D5244T23, D82PHEV, D87PHEV
- Volvo V70 (2008–)2009Tylko silnik: D5244T10
- Volvo V70 (2008–)2010Tylko silnik: D5244T10, D5244T14, D5244T19
- Volvo V70 (2008–)2011Tylko silnik: D5204T2, D5244T10
- Volvo V70 (2008–)2012Tylko silnik: D5204T3, D5244T11, D5244T15
- Volvo V70 (2008–)2013Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T15, D5244T17
- Volvo V70 (2008–)2014–2015Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17
- Volvo XC60 (2009–)2010Tylko silnik: D5244T10, D5244T14, D5244T16
- Volvo XC60 (2009–)2011Tylko silnik: D5204T2, D5244T10, D5244T16
- Volvo XC60 (2009–)2012Tylko silnik: D5204T3, D5244T11, D5244T15, D5244T17
- Volvo XC60 (2009–)2013Wszystkie silniki oprócz: B4204T7, B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2014Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17
- Volvo XC60 (2009–)2015Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17, D5244T23
- Volvo XC70 (2008–)2010Tylko silnik: D5244T10, D5244T14, D5244T16
- Volvo XC70 (2008–)2011Tylko silnik: D5204T2, D5244T10, D5244T16
- Volvo XC70 (2008–)2012–2013Wszystkie silniki oprócz: B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2014–2015Tylko silnik: D5204T3, D5244T11, D5244T12, D5244T15, D5244T17
Co oznacza ten kod błędu?
The engine control module monitors the accelerator pedal position sensor. The code is set when the module finds that the PWM (pulse-width modulated) signal from the pedal sensor has too low a frequency. The fault may lie in the signal or supply wire, or in the sensor itself.
Możliwe przyczyny
- An open circuit in the signal wire
- The signal wire is short-circuited to ground
- The signal wire is short-circuited to supply voltage
- The supply wire is short-circuited to ground
- The supply wire is short-circuited to supply voltage
- Damaged accelerator pedal position sensor
Co możesz zrobić
- 1Check that the fuses are intact
- 2With the ignition off, check that the connectors at the pedal sensor and the engine control module are secure and free from oxidation
- 3Look for breaks and chafing in the signal and supply wires to the pedal sensor, and use a multimeter to check that they have no contact with ground or supply voltage
- 4If you have a diagnostic tool, read the accelerator pedal position in live data and check that it follows the pedal as it is pressed and released
- 5If the fault remains, have a workshop with diagnostic equipment check the pedal sensor and its wiring
Objawy, które możesz zauważyć4
- A text message and a warning symbol appear in the display
- The engine hesitates or surges, and it is unclear when
- The engine hesitates or jerks during acceleration
- The engine hesitates or jerks during deceleration
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.