VOLVO
ECM-P21242F - Throttle/Pedal Position Sensor/Switch D Circuit Intermittent. General Signal Failures. Signal erratic
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The fault is intermittent, meaning it comes and goes, so it may not show up right now. The engine control module has registered that the analogue signal from the accelerator pedal sensor is incorrect, and compares it with the PWM signal. The code is only set if one of the codes ECM-P012000, ECM-P012200 or ECM-P012300 has been detected, and here the fault has not lasted long enough for that.
Możliwe przyczyny
- Contact resistance or oxidation in the connectors
- Damaged accelerator pedal position sensor
Co możesz zrobić
- 1Check that the fuses are intact
- 2Start the engine and read the accelerator pedal position in live data while slowly pressing and releasing the pedal. Check that the values follow the pedal and each other
- 3Check the connectors at the pedal sensor and the engine control module for contact resistance and oxidation. Loose connections are a common cause of intermittent faults
- 4If the fault is intermittent and does not show during these checks, test drive the car and read the code again afterwards
- 5If the fault remains, have a workshop decide whether the pedal sensor needs replacing
Objawy, które możesz zauważyć2
- A text message and a warning symbol appear in the display
- The engine lacks power and performs poorly
Na co może wpływać usterka1
- Engine torque may be limited
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.