VOLVO
ECM-P212835 - Throttle/Pedal Position Sensor/Switch E Circuit High. FM (Frequency Modulated) / PWM (Pulse Width Modulated) Failures. Signal high time above maximum
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The engine control module (ECM) checks that the two pedal signals follow each other as the pedal moves. The code is set when the PWM signal from the accelerator pedal sensor is too high. The fault may lie in the signal wire, the supply or the sensor itself.
Możliwe przyczyny
- Open circuit in the signal cable
- Signal cable short-circuited to ground
- Signal cable short-circuited to supply voltage
- Power supply cable short-circuited to ground
- Power supply cable short-circuited to supply voltage
- Damaged accelerator pedal position sensor
Co możesz zrobić
- 1Check that the fuses are intact; their locations are in the owner's manual or on the fuse box cover
- 2Road test the car and see whether hesitation, surging or jerky running occurs, and whether it happens right now
- 3With a diagnostic tool, start the engine and read the pedal movement in live data while pressing and releasing the pedal slowly
- 4Use a multimeter to check that the supply and signal wire to the pedal sensor have no open circuit or short to ground or supply voltage
- 5Check the connectors at the pedal sensor and the engine control module for contact resistance and oxidation
- 6Replace the pedal sensor only if the fault remains and nothing else is found
Objawy, które możesz zauważyć3
- Yellow warning symbol and a message in the display
- The car has poor performance and lacks power
- The engine hesitates, surges or runs jerkily
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.