VOLVO
ECM-P213500 - Throttle/Pedal Position Sensor/Switch A / B Voltage Correlation. General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
4 modeleS60 (2011–), S80 (2007–), V70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (11)
- Volvo S60 (2011–)2011–2012Tylko silnik: B5254T5
- Volvo S80 (2007–)2007Tylko silnik: B5254T6
- Volvo S80 (2007–)2008Tylko silnik: B4204S3, B4204S4, B5254T6
- Volvo S80 (2007–)2009Tylko silnik: B4204S3, B4204S4, B5254T6, B5254T8
- Volvo S80 (2007–)2010–2011Tylko silnik: B4204S3, B4204S4, B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2012Tylko silnik: B5254T10
- Volvo V70 (2008–)2008Tylko silnik: B4204S3, B4204S4, B5254T6
- Volvo V70 (2008–)2009Tylko silnik: B4204S3, B4204S4, B5254T6, B5254T8
- Volvo V70 (2008–)2010–2011Tylko silnik: B4204S3, B4204S4, B5254T10, B5254T11
- Volvo V70 (2008–)2012Tylko silnik: B5254T10
- Volvo XC90 (2003–)2005–2011Tylko silnik: B8444S
Co oznacza ten kod błędu?
This code never appears on its own. The engine control module (ECM) compares the PWM and analogue pedal signals and sets the code when they differ too much from each other. It is also set when one of the throttle position sensor circuit codes is stored, or when the two throttle unit potentiometers do not agree.
Możliwe przyczyny
- Poor connections, with high contact resistance, on the analogue signal wire
- Fault in the power supply to the analogue signal
- Fault in the analogue signal ground
- Fault in the PWM signal wire between the engine control module and the pedal sensor
- Damaged accelerator pedal sensor
- Fault in the throttle position sensor circuit of the electronic throttle unit
Co możesz zrobić
- 1Check that the fuses are intact; their locations are in the owner's manual or on the fuse box cover
- 2With a diagnostic tool, read both pedal signals in live data while pressing and releasing the pedal slowly; they should follow each other without sudden drops
- 3Check the connectors at the pedal sensor and the engine control module for contact resistance and oxidation
- 4Use a multimeter to check that the supply and ground wires to the pedal sensor have no open circuit
- 5Check the signal wire for open circuit and for contact with ground or supply voltage
- 6Replace the pedal sensor first only if the signals are wrong and the wiring is intact
Objawy, które możesz zauważyć5
- Message in the display
- Poor response from the accelerator pedal
- Accelerator pedal ignored when braking
- Maximum vehicle speed is reduced
- Malfunction indicator lamp (MIL) is lit
Na co może wpływać usterka2
- Acceleration is ignored when braking
- The control module uses the lowest value of the pedal position input signals
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.