VOLVO
ECM-P213862 - Throttle/Pedal Position Sensor/Switch D / E Voltage Correlation. Algorithm Based Failures. Signal compare failure
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
10 modeliC30 (2007–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (26)
- Volvo C30 (2007–2013)2011–2013Tylko silnik: D4162T
- Volvo S40 (2004–2013)2011–2012Tylko silnik: D4162T
- Volvo S60 (2011–)2011Wszystkie silniki oprócz: B5254T5, B6304T4, D5204T2, D5244T10
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7, D4162T
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3, D4162T
- Volvo S80 (2007–)2008–2009Tylko silnik: D4204T
- Volvo S80 (2007–)2010Tylko silnik: B4204T6, D4204T
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7, D4162T
- Volvo S80 (2007–)2015Tylko silnik: B4164T, D4162T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3, D4162T
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4, D4162T
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T, D4162T
- Volvo V50 (2004–2013)2011–2012Tylko silnik: D4162T
- Volvo V60 (2011–)2011Wszystkie silniki oprócz: B6304T4, D5204T2, D5244T10
- Volvo V60 (2011–)2012Wszystkie silniki oprócz: B6304T4, D5204T3, D5244T11, D5244T15
- Volvo V60 (2011–)2013–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7, D4162T
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3, D4162T
- Volvo V70 (2008–)2008–2009Tylko silnik: D4204T
- Volvo V70 (2008–)2010Tylko silnik: B4204T6, D4204T
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7, D4162T
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2, D4162T
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The engine control module (ECM) compares the analogue pedal signal, which travels via the central electronic module (CEM) over CAN, with the PWM signal that runs directly to the ECM. The code is set when the two signals do not follow each other. The fault may lie in the pedal sensor, its connectors or CEM.
Możliwe przyczyny
- Contact resistance or oxidation in the connections
- Fault in the CAN communication between the engine control module and the central electronic module (CEM)
- Fault in the pedal sensor PWM signal
- Fault in the analogue pedal sensor signal
- Damaged accelerator pedal sensor
- Fault in the central electronic module (CEM)
Co możesz zrobić
- 1Read the fault codes in the central electronic module (CEM) first, since the pedal signal passes through CEM
- 2With a diagnostic tool, read both pedal signals in live data while the pedal is pressed and released; they should follow each other
- 3Check that the fuses are intact; their locations are in the owner's manual or on the fuse box cover
- 4Check the connectors at the pedal sensor and the engine control module for contact resistance and oxidation
- 5Use a multimeter to check the supply and ground wires to the pedal sensor for open circuit
- 6If the checks reveal nothing and the fault persists, the pedal sensor can be swapped
Objawy, które możesz zauważyć2
- Yellow warning symbol and a message in the display
- The car has poor performance and lacks power
Na co może wpływać usterka1
- Engine torque and output may be limited
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.