VOLVO
ECM-P213886 - Throttle/Pedal Position Sensor/Switch D / E Voltage Correlation. Bus Signal / Message Failures. Signal invalid
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
12 modeliC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Pokaż modele wg rocznika i silnika (40)
- Volvo C30 (2007–2013)2011–2013Tylko silnik: D5204T, D5204T5
- Volvo C70 (2006–2013)2011Tylko silnik: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Wszystkie silniki oprócz: B5254T7
- Volvo S40 (2004–2013)2011–2012Tylko silnik: D5204T, D5204T5
- Volvo S60 (2011–)2011Tylko silnik: D5204T2, D5244T10
- Volvo S60 (2011–)2012Tylko silnik: D5204T3, D5244T11, D5244T15
- Volvo S60 (2011–)2013–2014Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S60 (2011–)2015Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T15, D5244T23
- Volvo S80 (2007–)2009Tylko silnik: D5244T10
- Volvo S80 (2007–)2010Tylko silnik: D5244T10, D5244T14, D5244T19
- Volvo S80 (2007–)2011Tylko silnik: D5204T2, D5244T10
- Volvo S80 (2007–)2012Tylko silnik: D5204T3, D5244T11, D5244T15
- Volvo S80 (2007–)2013–2014Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S80 (2007–)2015Tylko silnik: D5204T3, D5244T15
- Volvo V40 (2013–)2013–2014Tylko silnik: D5204T4, D5204T6
- Volvo V40 (2013–)2015Tylko silnik: D5204T6
- Volvo V40 Cross Country (2013–)2013–2014Tylko silnik: D5204T4, D5204T6
- Volvo V40 Cross Country (2013–)2015Tylko silnik: D5204T6
- Volvo V50 (2004–2013)2011–2012Tylko silnik: D5204T, D5204T5
- Volvo V60 (2011–)2011Tylko silnik: D5204T2, D5244T10
- Volvo V60 (2011–)2012Tylko silnik: D5204T3, D5244T11, D5244T15
- Volvo V60 (2011–)2013Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T15, D5244T17, D82PHEV
- Volvo V60 (2011–)2014Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17, D82PHEV
- Volvo V60 (2011–)2015Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17, D5244T23, D82PHEV, D87PHEV
- Volvo V70 (2008–)2009Tylko silnik: D5244T10
- Volvo V70 (2008–)2010Tylko silnik: D5244T10, D5244T14, D5244T19
- Volvo V70 (2008–)2011Tylko silnik: D5204T2, D5244T10
- Volvo V70 (2008–)2012Tylko silnik: D5204T3, D5244T11, D5244T15
- Volvo V70 (2008–)2013Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T15, D5244T17
- Volvo V70 (2008–)2014–2015Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17
- Volvo XC60 (2009–)2010Tylko silnik: D5244T10, D5244T14, D5244T16
- Volvo XC60 (2009–)2011Tylko silnik: D5204T2, D5244T10, D5244T16
- Volvo XC60 (2009–)2012Tylko silnik: D5204T3, D5244T11, D5244T15, D5244T17
- Volvo XC60 (2009–)2013Wszystkie silniki oprócz: B4204T7, B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2014Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17
- Volvo XC60 (2009–)2015Tylko silnik: D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17, D5244T23
- Volvo XC70 (2008–)2010Tylko silnik: D5244T10, D5244T14, D5244T16
- Volvo XC70 (2008–)2011Tylko silnik: D5204T2, D5244T10, D5244T16
- Volvo XC70 (2008–)2012–2013Wszystkie silniki oprócz: B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2014–2015Tylko silnik: D5204T3, D5244T11, D5244T12, D5244T15, D5244T17
Co oznacza ten kod błędu?
The engine control module (ECM) compares the PWM signal with the analogue signal from the pedal sensor, and the code is set when the difference between them becomes too great. The fault may lie in the pedal sensor, its connectors, the ground wire or the wires of the CAN network.
Możliwe przyczyny
- Poor contact or oxidation in the pedal sensor connections
- Open circuit in the ground wire or the signal ground wire
- Fault in the pedal sensor PWM signal
- Fault in the pedal sensor analogue signal
- Damaged accelerator pedal sensor
- Open or short circuit between the CAN network wires
Co możesz zrobić
- 1Check that the fuses are intact; their locations are in the owner's manual or on the fuse box cover
- 2Check the connectors at the pedal sensor and the engine control module for contact resistance and oxidation, and make sure none is loose
- 3Use a multimeter to check that the ground lead to the pedal sensor has no open circuit
- 4With a diagnostic tool, read the pedal value in live data while the pedal is pressed and released, and check that it follows the movement
- 5Have a workshop with diagnostic equipment check the CAN network wires for open circuit and short circuit
- 6Replace the pedal sensor first only if the other checks show no other fault
Objawy, które możesz zauważyć3
- Yellow warning symbol and a message in the display
- The car lacks power
- The engine hesitates, surges or runs jerkily during acceleration or deceleration
Na co może wpływać usterka1
- Engine output may be limited
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.