VOLVO
ECM-P230412 - Ignition Coil B Primary Control Circuit High. General Electrical Failures. Circuit short to battery
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The engine control module (ECM) monitors the signal line to the ignition coil primary winding. The code is set when the signal is too high, which in this case means the signal line to ignition coil 2 has been short-circuited to supply voltage. It is an electrical fault in the circuit, and the code applies only to this ignition coil.
Możliwe przyczyny
- The signal wire to ignition coil 2 is short-circuited to supply voltage
- The ignition coil is damaged
Co możesz zrobić
- 1Check that the relevant fuses are intact; their locations are shown in the car's owner's manual
- 2Read and note the code, clear it and run the engine for a while to see whether it returns
- 3Inspect the connector and cable at ignition coil 2 for loose contacts, corrosion, chafing and pinching
- 4Use a multimeter to check that the signal wire to ignition coil 2 has no contact with supply voltage
- 5If the fault returns, have a workshop with diagnostic equipment check the ignition coil and its wiring
Objawy, które możesz zauważyć2
- The engine warning lamp (Check engine) lights up or behaves abnormally
- The car runs poorly and lacks power
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.