VOLVO
ECM-P250A13 - Engine Oil Level Sensor Circuit. General Electrical Failures. Circuit open
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
8 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Pokaż modele wg rocznika i silnika (17)
- Volvo S60 (2011–)2011–2012Tylko silnik: B5254T5
- Volvo S60 (2011–)2014–2015Tylko silnik: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, D4204T5
- Volvo S80 (2007–)2007–2008Tylko silnik: B5254T6
- Volvo S80 (2007–)2009Tylko silnik: B5254T6, B5254T8
- Volvo S80 (2007–)2010–2011Tylko silnik: B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2012Tylko silnik: B5254T10
- Volvo S80 (2007–)2014–2015Tylko silnik: B4204T11, B4204T12, B4204T15, D4204T5
- Volvo V40 (2013–)2015Tylko silnik: B4204T11, D4204T14
- Volvo V40 Cross Country (2013–)2015Tylko silnik: B4204T11, D4204T14
- Volvo V60 (2011–)2014–2015Tylko silnik: B4204T11, B4204T12, B4204T15, B4204T9, D4204T5
- Volvo V70 (2008–)2008Tylko silnik: B5254T6
- Volvo V70 (2008–)2009Tylko silnik: B5254T6, B5254T8
- Volvo V70 (2008–)2010–2011Tylko silnik: B5254T10, B5254T11
- Volvo V70 (2008–)2012Tylko silnik: B5254T10
- Volvo V70 (2008–)2014–2015Tylko silnik: B4204T11, D4204T5
- Volvo XC60 (2009–)2014–2015Tylko silnik: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, D4204T5
- Volvo XC70 (2008–)2014–2015Tylko silnik: B4204T11, D4204T5
Co oznacza ten kod błędu?
The ECM reads the signal from the oil level sensor and uses it to monitor the oil level. The code is stored when that signal is incorrect, which may be an electrical fault in the sensor or its wiring. Water or fuel in the engine oil can also trigger it.
Możliwe przyczyny
- Contact resistance, oxidation or loose contact in the connections
- Open circuit in the signal wire
- Open circuit in the power supply
- Water or fuel in the engine oil
- Damaged oil level sensor
Co możesz zrobić
- 1Read the fault status with the engine running. If the code is not active, the fault may have been intermittent
- 2Check that the relevant fuses are intact
- 3Check whether water or fuel may have got into the engine oil. If so, the code can be set, and the remedy is to run the engine fully warm
- 4Use a multimeter to check that the power supply and signal wire to the oil level sensor have no open circuit
- 5If the fault remains after these checks, have a workshop with diagnostic equipment check the oil level sensor
Objawy, które możesz zauważyć1
- The oil pressure warning lamp comes on or behaves abnormally
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.