VOLVO
ECM-U011181 - Lost Communication With Battery Energy Control Module "A". Bus Signal / Message Failures. Invalid serial data received
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The engine control module (ECM) constantly receives data over the CAN network from the central electronics control module (CEM). The code is set when the engine control module detects faulty CAN communication. Although the code is titled lost communication with the battery energy control module “A”, it applies to the CAN communication between the engine control module and the central electronics control module.
Możliwe przyczyny
- Fault in the central electronics control module (CEM)
- Intermittent breaks in one or both CAN wires
- Intermittent short circuits between the CAN wires, or between a CAN wire and ground or supply voltage
- The sending control module has stopped sending the signal the engine control module expects
- Incorrect signal configuration in a control module that was replaced without new software being loaded
Co możesz zrobić
- 1Read the codes in the engine control module and first fix any other CAN-related codes, as they may share the same cause
- 2Clear the code and road test the car to see if it is set again
- 3Check the CAN wiring between the engine control module and the central electronics control module for chafing, pinched areas and loose connectors
- 4Use a multimeter to check that the CAN wires have no break and are not shorted to ground or supply voltage
- 5Check that the battery has good voltage and that the fuses are intact
- 6If the fault returns: have a workshop with diagnostic equipment check the central electronics control module. Do not work on the battery system yourself
Objawy, które możesz zauważyć1
- No noticeable symptoms for the driver
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.