VOLVO
ECM-U012008 - Lost Communication with Starter/ Generator Control Module. General Failure Information. Bus Signal / Message Failures
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The engine control module (ECM) communicates with the alternator control module (ACM) over LIN. The code is set when the communication is faulty, or when the alternator control module sends fault information to the engine control module. Although the code is titled lost communication with the starter/generator control module, it concerns communication between the engine control module and the alternator control module.
Możliwe przyczyny
- Contact resistance or oxidation in the connectors
- Open circuit in the signal wire
- Faulty alternator control module (ACM)
- Faulty alternator
Co możesz zrobić
- 1Check that the fuses are intact
- 2Check the connectors at the alternator control module for contact resistance and oxidation
- 3Look for breaks, chafing or pinched areas on the signal wire between the engine control module and the alternator control module. Use a multimeter to check that the wire has no break
- 4Clear the code and road test the car. If you have a diagnostic tool, check that the code's diagnostic status shows the fault is no longer present
- 5If the fault returns: have a workshop with diagnostic equipment check the alternator and its control module
Objawy, które możesz zauważyć1
- The engine does not start
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.