VOLVO
ECM-U030000 - Internal Control Module Software Incompatibility. General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
14 modeliC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (17)
- Volvo C30 (2007–2013)2011–2013Tylko silnik: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Tylko silnik: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Wszystkie silniki oprócz: B5254T7
- Volvo S40 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V40 (2013–)2013–2015
- Volvo V40 Cross Country (2013–)2013–2015
- Volvo V50 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2015
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
- Volvo XC90 (2003–)2007–2010Tylko silnik: B6324S
- Volvo XC90 (2003–)2011–2012Tylko silnik: B6324S5
- Volvo XC90 (2003–)2013–2014Wszystkie silniki oprócz: B5254T9
Co oznacza ten kod błędu?
The engine control module (ECM) compares its own configuration ID with the ID that the central electronics control module (CEM) sends out on the CAN network. The code is set when the IDs do not match, and also when communication with the CEM is or has been interrupted. Although the code is titled internal software incompatibility, it concerns a configuration ID that does not match the CEM.
Możliwe przyczyny
- Wrong configuration ID because the module is not intended for the car, for example a used module with different software or hardware
- Break in the CAN wires between the engine control module and the CEM
- Intermittent breaks on one or both CAN wires
Co możesz zrobić
- 1Read the codes in the central electronics control module and other control modules, and fix communication faults first
- 2Check that the fuses are intact
- 3Check the CAN connectors for contact resistance and oxidation
- 4Look for chafed CAN wires. Use a multimeter to check that they have no break or short to ground or supply voltage
- 5If the module was recently replaced: have a workshop check that it is intended for this car and has the correct software and configuration
Objawy, które możesz zauważyć5
- The cruise control does not work at all
- The engine jerks on throttle and sharply after engine braking
- Uneven idle
- The engine does not start
- The general warning lamp is on
Na co może wpływać usterka2
- The module shuts off from the CAN network (bus-off) and stops sending messages
- The module's functions stop working
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.