VOLVO
ECM-U201200 - Car Configuration Parameter(s). General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
5 modeliS80 (2007–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (14)
- Volvo S80 (2007–)2007–2008Tylko silnik: D5244T4, D5244T5
- Volvo S80 (2007–)2009Tylko silnik: D5244T10, D5244T4, D5244T5
- Volvo S80 (2007–)2010Tylko silnik: D4164T, D5244T10, D5244T14, D5244T19
- Volvo S80 (2007–)2011Tylko silnik: D4164T
- Volvo V70 (2008–)2008Tylko silnik: D5244T4, D5244T5
- Volvo V70 (2008–)2009Tylko silnik: D5244T10, D5244T4, D5244T5
- Volvo V70 (2008–)2010Tylko silnik: D4164T, D5244T10, D5244T14, D5244T19
- Volvo V70 (2008–)2011Tylko silnik: D4164T
- Volvo XC60 (2009–)2009Wszystkie silniki oprócz: B6304T2
- Volvo XC60 (2009–)2010Tylko silnik: D5244T10, D5244T14, D5244T16
- Volvo XC70 (2008–)2008Wszystkie silniki oprócz: B6324S
- Volvo XC70 (2008–)2009Tylko silnik: D5244T4, D5244T5
- Volvo XC70 (2008–)2010Tylko silnik: D5244T10, D5244T14, D5244T16
- Volvo XC90 (2003–)2013–2014Tylko silnik: D5244T18, D5244T5
Co oznacza ten kod błędu?
The engine control module (ECM) checks its own configuration ID against the signal setup that the CEM broadcasts on the CAN network. The modules on the network must share the same signal configuration ID to communicate. The code is set when the module's own ID differs from the one the CEM sends out, and the fault may be because the module is not intended for this car.
Możliwe przyczyny
- Incorrect configuration ID, because the module is not intended for the car, for example a used module with different software or hardware
- Open circuit in the CAN cables between the module and the central electronic module (CEM)
- Fault in the central electronic module (CEM)
Co możesz zrobić
- 1Check whether the engine control module is a used module or has been replaced recently. Tell the workshop, since the module must be intended for this car.
- 2Read the fault codes in the central electronic module (CEM) and remedy any faults there first. Do not replace the CEM for a CAN fault unless troubleshooting shows an internal fault.
- 3Look for loose or chafed wires and connectors on the CAN network between the ECM and the CEM. Gently wiggle them to see whether the fault appears.
- 4If a module was replaced without new software being loaded, have a workshop download the correct software, as this requires programming.
Objawy, które możesz zauważyć2
- Cruise control cannot be engaged
- Red warning symbol and message in the display
Na co może wpływać usterka1
- The control module shuts itself off (bus-off)
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.