What does fault code P060C mean?

The control module has detected a fault in the Internal Control Module Main Processor Performance (P060C). The underlying code points specifically at the main processor and its watchdog circuit. Measurements: • Internal Control Module Main Processor Performance – Permanent B+ Supply (Voltage (V)): 12.4 - 12.7 V (ignition OFF) / 13.5 - 14.7 V (engine running) [Condition: At module supply pins] • Internal Control Module Main Processor Performance – Ignition-Switched Supply (Voltage (V)): 11.8 - 14.4 V [Condition: Ignition ON] • Internal Control Module Main Processor Performance – Ground Connections Voltage Drop (Voltage (V)): < 0.1 V per ground point [Condition: Under load to battery negative] • Internal Control Module Main Processor Performance – 5 V Reference Outputs (Voltage (V)): 4.95 - 5.05 V per circuit [Condition: Ignition ON, sensors unplugged one at a time] Oscilloscope: Log module supply voltage during cranking and load changes. It must not fall below 9.5 V on start or carry high-frequency noise that disturbs the processor. (Scale: 500 ms/div, 5 V/div)

What are the symptoms of fault code P060C?

Subsystem operating efficiency falls below calibrated threshold Check Engine Light (MIL) illuminated Possible drivability or power reduction Risk of failing an emissions inspection

What causes fault code P060C?

Most likely: Internal processor or watchdog reset, often from voltage spikes, heat, or cold solder joints inside the module Most likely: Internal Control Module Main Processor Performance is electrically operational but performing outside calibrated tolerance Likely: Chafed or pinched wiring harness along the signal path to Internal Control Module Main Processor Performance Likely: Poor ground connection or excessive voltage drop (> 0.1 V) at the ground point for Internal Control Module Main Processor Performance Rare: Defective internal output driver or reference circuit in the control module for Internal Control Module Main Processor Performance

How do you fix fault code P060C?

Check supply quality and ground, look for water ingress at the module connector, and heat/cool the module while logging — if the reset returns the board is at fault. Verify underlying mechanical operation and rule out blockage, vacuum leaks, or mechanical binding. Verify loaded supply voltage and harness terminal pins at Internal Control Module Main Processor Performance. Check circuit continuity and ground-side voltage drop (< 0.05 V) for Internal Control Module Main Processor Performance. Inspect module enclosure and connector headers for water ingress, fretting corrosion, or PCB thermal damage. Mechanic tip: A resetting processor often sets a swarm of consequential codes — clear all, road test, and see which code returns FIRST.

Standard EOBD

P060C - Intern styreenhetsfeil Main Processor – urimelig verdi

Q: What are the symptoms of fault code P060C?

Subsystem operating efficiency falls below calibrated threshold Check Engine Light (MIL) illuminated Possible drivability or power reduction Risk of failing an emissions inspection

Q: What causes fault code P060C?

Most likely: Internal processor or watchdog reset, often from voltage spikes, heat, or cold solder joints inside the module Most likely: Internal Control Module Main Processor Performance is electrically operational but performing outside calibrated tolerance Likely: Chafed or pinched wiring harness along the signal path to Internal Control Module Main Processor Performance Likely: Poor ground connection or excessive voltage drop (> 0.1 V) at the ground point for Internal Control Module Main Processor Performance Rare: Defective internal output driver or reference circuit in the control module for Internal Control Module Main Processor Performance

Relatert:Intern styreenhetsfeil Main Processor, Ledningsnett og kontakter, Styreenhet (ECM/PCM)

System

Drivlinje (Motor og girkasse)

Kontakt oss Finn reparasjon

Teknisk beskrivelse

Styreenheten registrerer en feil i Intern styreenhetsfeil Main Processor (P060C). Koden peker spesifikt på hovedprosessor og watchdog.

Multimeter Målepunkter & Nominelle Verdier

Målepunkt / Komponent	Måletype	Nominelt Målområde	Målevilkår
Intern styreenhetsfeil Main Processor – permanent matespenning	Spenning (V)	12.4 - 12.7 V / 13.5 - 14.7 V	Ved modulens pinner
Intern styreenhetsfeil Main Processor – jordforbindelser spenningsfall	Spenning (V)	< 0.1 V	Under belastning

Intern styreenhetsfeil Main Processor – permanent matespenningSpenning (V)

Børverdi:12.4 - 12.7 V / 13.5 - 14.7 V

Ved modulens pinner

Intern styreenhetsfeil Main Processor – jordforbindelser spenningsfallSpenning (V)

Børverdi:< 0.1 V

Under belastning

Oscilloskop Kurveformanalyse

500 ms/div, 5 V/div

Logg matespenningen under start; må ikke falle under 9.5 V.

Mulige årsaker

Intern prosessor-/watchdog-reset

Intern styreenhetsfeil Main Processor fungerer elektrisk, men yter utenfor toleranse

Gnagd eller klemt ledningsnett fram til Intern styreenhetsfeil Main Processor

Dårlig jordforbindelse eller spenningsfall (> 0.1 V) for Intern styreenhetsfeil Main Processor

Defekt driver eller referanseutgang i styreenheten for Intern styreenhetsfeil Main Processor

Symptomer

Systemets virkningsgrad faller under kalibrert grense

Motorlampe (MIL) lyser

Mulig redusert kjørbarhet eller effekt

Risiko for underkjent EU-kontroll

Anbefalt tiltak

Kontroller matning og jord, se etter vanninntrengning.

Sjekk mekanisk grunnfunksjon og utelukk lekkasjer eller tette kanaler.

Sjekk matespenning og kontaktstykke ved Intern styreenhetsfeil Main Processor.

Mål kontinuitet og jordspenningsfall (< 0.05 V) for Intern styreenhetsfeil Main Processor.

Sjekk kontaktdon og kretskort for fukt og korrosjon.

Mekanikerens tips

En resettende prosessor gir ofte mange følgekoder.

Relaterte feilkoder

P064C

Glødepluggstyreenhet (GPCM) 1

P0652

sensor referansespenning 'B' – lavt signal

P067B

Sylinder 4 Glødeplugg – styrekrets høyt signal

P064F

Uautorisert programvare detektert

Målepunkt / Komponent

Måletype

Nominelt Målområde

Målevilkår

Intern styreenhetsfeil Main Processor – permanent matespenning

Spenning (V)

12.4 - 12.7 V / 13.5 - 14.7 V

Ved modulens pinner

Intern styreenhetsfeil Main Processor – jordforbindelser spenningsfall

Spenning (V)

< 0.1 V

Under belastning