VOLVO
BCM-0148 - Communication between control modules. Faulty configuration ID
System
Brake Control Module (BCM)
Volvo models this fault code applies to
Applies to the following models:
10 modelsC30 (2007–2013), C30 Electric (2011–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (21)
- Volvo C30 (2007–2013)2007–2011
- Volvo C30 (2007–2013)2012All engines except: D4162T, D5204T, D5204T5
- Volvo C30 (2007–2013)2013Engine B4204S3, B4204S4, B5254T7 only
- Volvo C30 Electric (2011–2013)2011–2013
- Volvo C70 (2006–2013)2006–2011
- Volvo C70 (2006–2013)2012–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2004–2010
- Volvo S40 (2004–2013)2011–2012All engines except: D4162T, D5204T, D5204T5
- Volvo S60 (2001–2009)2002–2009
- Volvo S80 (1999–2006)2002–2006
- Volvo V50 (2004–2013)2004–2010
- Volvo V50 (2004–2013)2011–2012All engines except: D4162T, D5204T, D5204T5
- Volvo V70 (2000–2008)2002–2008
- Volvo V70 XC / XC70 (2001–2007)2002–2007
- Volvo XC90 (2003–)2003–2004, 2015
- Volvo XC90 (2003–)2005–2006All engines except: B8444S
- Volvo XC90 (2003–)2007Engine B5254T2, D5244T4 only
- Volvo XC90 (2003–)2008–2010All engines except: B6324S, B8444S
- Volvo XC90 (2003–)2011All engines except: B6324S5, B8444S
- Volvo XC90 (2003–)2012All engines except: B6324S5
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
What does this fault code mean?
The steering angle sensor module (SAS) and the steering wheel module (SWM) send data to the brake control module in small packets, and each packet has an identifier number. The code is set if the brake control module receives an identifier that does not match the one it expects. The code may be stored when the brake control module is programmed.
Possible causes
- Interference or intermittent breaks on the CAN network
- Internal fault in the steering angle sensor module (SAS)
- Fault inside the steering wheel module (SWM)
What you can do
- 1Clear the code if it was set during programming of the brake control module, and check that it does not return
- 2Read the codes in the steering angle sensor module and the steering wheel module and fault-find according to them
- 3Check the CAN communication with diagnostic equipment, and replace the steering angle sensor module if it is faulty
- 4The brake system is safety critical: do not replace the brake control module for this code, and drive carefully until the fault is fixed
Symptoms you may notice5
- Anti-spin warning lamp on
- General yellow warning lamp on
- Anti-spin does not work
- Stability function does not work
- Anti-skid does not work
What the fault can affect1
- Traction control (TC), stability control (SC) and active yaw control (AYC) are disabled
General guidance for car owners. Diagnosis on the car can point to a different cause.