VOLVO
BCM-C002071 - ABS Pump Motor Control. Mechanical Failures. Actuator stuck
System
Brake Control Module (BCM)
Volvo models this fault code applies to
Applies to the following models:
14 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Show models by year and engine (19)
- Volvo C30 (2007–2013)2011–2013Engine D4162T, D5204T, D5204T5 only
- Volvo C70 (2006–2013)2011Engine D5204T, D5204T5 only
- Volvo C70 (2006–2013)2012–2013All engines except: B5254T7
- Volvo S40 (2004–2013)2011–2012Engine D4162T, D5204T, D5204T5 only
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V40 (2013–)2013–2015
- Volvo V40 Cross Country (2013–)2013–2015
- Volvo V50 (2004–2013)2011–2012Engine D4162T, D5204T, D5204T5 only
- Volvo V60 (2011–)2011–2015
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
- Volvo XC90 (2003–)2005–2006Engine B8444S only
- Volvo XC90 (2003–)2007–2010Engine B6324S, B8444S only
- Volvo XC90 (2003–)2011Engine B6324S5, B8444S only
- Volvo XC90 (2003–)2012Engine B6324S5 only
- Volvo XC90 (2003–)2013–2014All engines except: B5254T9
What does this fault code mean?
The brake control module (BCM) has commanded the ABS pump motor but found that it does not start or does not run as it should, interpreted as the pump being stuck. The pump motor builds the brake pressure needed for ABS and stability control.
Possible causes
- Contact resistance in the connections to the pump motor
- Wrong fuse for the pump motor
- Open circuit in the supply or ground wire to the pump motor
- Damaged or seized pump motor
- Faulty brake control module (uncommon)
What you can do
- 1Read and note the code, clear it and road test the car to see whether it returns
- 2Check the pump motor fuse and that the correct fuse is fitted
- 3Check that the connectors at the brake control module and the pump motor are secure and free from oxidation
- 4With diagnostic equipment activate the pump motor and check that it starts and runs normally
- 5If the pump motor does not start, the hydraulic unit normally needs replacing by a workshop
- 6The braking system is safety critical: do not work on the pump motor or hydraulic unit yourself, and drive carefully until the fault is fixed
Symptoms you may notice5
- General warning lamp and ABS warning lamp on
- ABS, traction control and stability function do not work
- Adaptive cruise control and collision warning do not work
- Electronic parking brake has reduced function
- Front monitoring and City Safety do not work
What the fault can affect2
- ABS, traction control, stability control and brake assistance are blocked
- Active yaw control (AYC) is blocked
General guidance for car owners. Diagnosis on the car can point to a different cause.