VOLVO
ECM-126C - Boost pressure sensor. Signal too high
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
The engine control module (ECM) monitors the signal from the boost pressure sensor. If the signal stays above a set level long enough, the fault is stored, meaning the sensor reports values that are too high. The cause is most often a connection problem or a wiring fault, but the sensor can also be damaged.
Possible causes
- Contact resistance or oxidation at the connections
- Signal wire shorted to voltage
- Open circuit in the signal wire
- Open circuit in the signal ground wire
- Damaged boost pressure sensor
What you can do
- 1Read the fault code, clear it and test drive the car to see whether it returns
- 2Check that the boost pressure sensor connector is fully seated and free from oxidation
- 3Check the signal wire for breaks and chafing; with a multimeter, confirm it has no contact with voltage
- 4Check that the signal ground wire between the sensor and the control module has no open circuit
- 5If you have a diagnostic tool: read boost pressure in live data at idle and under throttle, and check that the value follows the throttle smoothly without sudden jumps
Symptoms you may notice2
- Engine warning lamp comes on
- Noticeably reduced performance
What the fault can affect1
- Boost pressure is limited
General guidance for car owners. Diagnosis on the car can point to a different cause.