VOLVO
ECM-1310 - Air mass. Signal too low
System
Engine Control Module (ECM)
Volvo models this fault code applies to
This fault code has different meanings depending on model, model year or engine. Select the meaning that applies to your car.
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The engine control module (ECM) continuously checks that the MAF sensor signal is plausible and follows the sensor's normal characteristic. The fault is set if the signal is too high or too low. Although the code is labelled too low, a signal that is too high can set it as well.
Possible causes
- Open circuit in the ground wire to the MAF sensor
- Damaged MAF sensor
- Signal wire shorted to ground
What you can do
- 1Read the fault code, clear it and test drive to see whether it returns
- 2Check that the MAF sensor connectors are free from contact resistance, play and oxidation
- 3With a multimeter, check that the ground wire to the MAF sensor has no open circuit
- 4With a multimeter, check that the signal wire is not shorted to ground
- 5If you have a diagnostic tool: read air mass in live data with the engine running and check that it rises as engine speed rises
- 6If the wiring is fine: have a workshop check the MAF sensor
Symptoms you may notice1
- Reduced performance
What the fault can affect1
- A calculated air mass is used instead of the sensor reading
General guidance for car owners. Diagnosis on the car can point to a different cause.