VOLVO
ECM-1840 - Swirl actuator control. Faulty signal
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The ECM monitors the signal going to the swirl throttle motor, which operates the swirl flaps in the intake. If the signal is judged to be incorrect the code is set. The fault can be caused by an open circuit or short circuit in the wiring, or by a damaged swirl throttle motor. It may give a message in the information display.
Possible causes
- Open circuit or short to supply voltage in the signal wire
- Power supply wire short-circuited to battery voltage
- Open circuit in the ground wire
- Damaged swirl throttle motor
What you can do
- 1Read and clear the fault code and check whether it returns
- 2Check the connector at the swirl throttle motor for play, oxidation and corrosion
- 3Check that the wiring to the swirl throttle motor is not chafed or pinched
- 4Use a multimeter to check that the signal wires have no open circuit and are not short-circuited to voltage, and that the ground wire has no open circuit
- 5If you have a diagnostic tool, activate the swirl throttle motor and listen for a ticking sound when it starts
Symptoms you may notice1
- A message appears in the information display
General guidance for car owners. Diagnosis on the car can point to a different cause.