VOLVO
ECM-23B0 - Injector cyl 2. Signal missing
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine D4164T, D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D4164T, D5244T13, D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2011Engine D4164T only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2005, 2011Engine D4164T only
- Volvo S40 (2004–2013)2006Engine D4164T, D5244T8 only
- Volvo S40 (2004–2013)2007Engine D4164T, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D4164T, D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2005, 2011Engine D4164T only
- Volvo V50 (2004–2013)2006Engine D4164T, D5244T8 only
- Volvo V50 (2004–2013)2007Engine D4164T, D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D4164T, D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012Engine D5244T18, D5244T5 only
What does this fault code mean?
The engine control module (ECM) registers that the signal to the injector for cylinder 2 is missing. The fault comes from a break in the signal wire, a damaged injector or a break in the wiring to the injector.
Possible causes
- Open circuit in the signal wire
- Break in the wiring to the injector
- Damaged injector
What you can do
- 1Clear the code after reading it, then road test to see whether it returns
- 2Follow the wire from injector 2 back toward the engine control module and look for breaks or loose connectors
- 3Check that the connector at valve 2 is clean and secure
- 4If you have a diagnostic tool: activate injector 2 and check that it clicks
- 5If the fault remains, have a workshop measure the valve resistance and check the wiring
Symptoms you may notice4
- Engine fails to start
- Message in the display
- Running is poorer, with hesitation and jerkiness
- Malfunction indicator lamp (MIL) lit
What the fault can affect1
- No injection takes place in cylinder 2
General guidance for car owners. Diagnosis on the car can point to a different cause.