VOLVO
ECM-23C0 - Injector cyl 3. Signal missing
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine D4164T, D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D4164T, D5244T13, D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2011Engine D4164T only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2005, 2011Engine D4164T only
- Volvo S40 (2004–2013)2006Engine D4164T, D5244T8 only
- Volvo S40 (2004–2013)2007Engine D4164T, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D4164T, D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2005, 2011Engine D4164T only
- Volvo V50 (2004–2013)2006Engine D4164T, D5244T8 only
- Volvo V50 (2004–2013)2007Engine D4164T, D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D4164T, D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012Engine D5244T18, D5244T5 only
What does this fault code mean?
The ECM watches the signal feeding the cylinder 3 injector. If the signal is missing, the code is set and injection in that cylinder stops. The likely causes are a break in the wire or a damaged injector.
Possible causes
- Open circuit in the wiring to the injector
- Open circuit in the signal wire
- Damaged injector
What you can do
- 1Read the code, clear it and road test
- 2Use a multimeter to check that the wire to injector 3 runs all the way through
- 3Look at the connector at valve 3: it should be firmly seated and clean
- 4If you have a diagnostic tool: activate injector 3 and listen for a click
- 5If the fault remains, have a workshop decide whether the valve or the wiring needs replacing
Symptoms you may notice4
- Engine fails to start
- Message in the display
- Poor performance and lack of power
- Malfunction indicator lamp (MIL) lit
What the fault can affect1
- Injection in cylinder 3 stops
General guidance for car owners. Diagnosis on the car can point to a different cause.