VOLVO
ECM-23D0 - Injector cyl 4. Signal missing
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine D4164T, D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D4164T, D5244T13, D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2011Engine D4164T only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2005, 2011Engine D4164T only
- Volvo S40 (2004–2013)2006Engine D4164T, D5244T8 only
- Volvo S40 (2004–2013)2007Engine D4164T, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D4164T, D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2005, 2011Engine D4164T only
- Volvo V50 (2004–2013)2006Engine D4164T, D5244T8 only
- Volvo V50 (2004–2013)2007Engine D4164T, D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D4164T, D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012Engine D5244T18, D5244T5 only
What does this fault code mean?
The engine control module (ECM) monitors the signal to the injector for cylinder 4. When it is missing, the code is set. The cause may be a break in the signal wire, in the wiring to the valve or a faulty injector.
Possible causes
- Signal wire is broken
- Break in the wiring to the injector
- Damaged injector
What you can do
- 1Read the code and clear it, then road test to see whether it comes back
- 2Trace the cable from injector 4 to the engine control module and check that it is intact
- 3Check the connector at the valve: it should be secure and clean
- 4If you have a diagnostic tool: activate injector 4 and see whether it clicks when activated
- 5If the fault remains, have a workshop check the valve
Symptoms you may notice4
- Engine fails to start
- Message in the display
- Running feels weak and jerky
- Malfunction indicator lamp (MIL) lit
What the fault can affect1
- No fuel is sprayed into cylinder 4
General guidance for car owners. Diagnosis on the car can point to a different cause.