VOLVO
ECM-2410 - Fuel system. Signal missing
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine D4164T, D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D4164T, D5244T13, D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2011Engine D4164T only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2005, 2011Engine D4164T only
- Volvo S40 (2004–2013)2006Engine D4164T, D5244T8 only
- Volvo S40 (2004–2013)2007Engine D4164T, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D4164T, D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2005, 2011Engine D4164T only
- Volvo V50 (2004–2013)2006Engine D4164T, D5244T8 only
- Volvo V50 (2004–2013)2007Engine D4164T, D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D4164T, D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The ECM monitors the signal going to the injection valves. If it receives no signal, it treats this as a fault and the code is stored. Without the signal, injection stops, so the engine cannot start or run normally.
Possible causes
- Open circuit in the cables to the injection valves
- Damaged injection valve
- Internal electronic fault in the ECM
What you can do
- 1Read and note the code, clear it and try starting the engine to see whether the code returns
- 2Check that the connectors at the injection valves are fully engaged and not corroded
- 3Follow the cables to the injection valves and look for chafing, pinch damage and loose clips
- 4Use a multimeter to check that the cables have no open circuit, and repair any break before going further
- 5If the cables and connectors are intact, have a workshop with diagnostic equipment check the injection valves and the control module
Symptoms you may notice2
- The engine does not start
- A message appears in the display
What the fault can affect1
- Injection stops
General guidance for car owners. Diagnosis on the car can point to a different cause.