VOLVO
ECM-242D - Front heated oxygen sensor (HO2S), bank 1. Slow regulation
System
Engine Control Module (ECM)
Volvo models this fault code applies to
This fault code has different meanings depending on model, model year or engine. Select the meaning that applies to your car.
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2006–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2006–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
The front heated oxygen sensor (HO2S) on bank 1 responds too slowly to changes in the exhaust gases and in the fuel/air mixture. The ECM checks how well the sensor has aged and stores the code when its response has become too slow.
Possible causes
- Short circuit between the cables for calibration current and pump current
- Open circuit in the signal cable (-)
- Open circuit in the cable for calibration current
- Damaged front heated oxygen sensor
What you can do
- 1Read and note the code, clear it and road test to see whether it returns
- 2Check that the connector at the oxygen sensor is fully engaged and not corroded. Do not use rust solvent spray or grease in the connector
- 3Follow the cables from the oxygen sensor and look for chafing and damage, especially near the exhaust pipe
- 4Use a multimeter to check that the signal cable and the calibration current cable have no open circuit and are not short-circuited to each other
- 5If the cables are intact, have a workshop with diagnostic equipment check the function of the oxygen sensor
Symptoms you may notice1
- The malfunction indicator lamp (MIL) is lit
What the fault can affect1
- Catalytic converter diagnostics are switched off
General guidance for car owners. Diagnosis on the car can point to a different cause.