VOLVO
ECM-244C - Front heated oxygen sensor (HO2S), bank 1, heating. Signal too high
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
The fault applies to the heating of the front oxygen sensor on bank 1. The engine control module (ECM) pulses the current to the sensor heating element and checks the signal. The code is stored when the signal reads over a set threshold with the heating active.
Possible causes
- Signal cable short-circuited to supply voltage
- Damaged front heated oxygen sensor
What you can do
- 1Read and note the code, clear it and road test to see whether it comes back
- 2Check the oxygen sensor connector for oxidation and loose connections. Do not use rust solvent spray or grease in it
- 3If possible, take readings from the cable side of the connector so you do not damage it or create a loose contact later
- 4Use a multimeter to check that the signal cable is not short-circuited to supply voltage, meaning plus on the car
- 5If the cables are intact but the fault remains, have a workshop try a new oxygen sensor
Symptoms you may notice1
- The malfunction indicator lamp (MIL) is lit
What the fault can affect2
- Oxygen sensor control is switched off
- Fuel trim control based on the oxygen sensor is switched off
General guidance for car owners. Diagnosis on the car can point to a different cause.