VOLVO
ECM-2510 - Fuel pressure. Signal too low
System
Engine Control Module (ECM)
Volvo models this fault code applies to
This fault code has different meanings depending on model, model year or engine. Select the meaning that applies to your car.
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The ECM monitors the fuel pressure sensor signal. At engine start and switch-off the fuel pressure is expected to reach a specific value within a short time. If the sensor value deviates too much from the calculated one, here too low, the code is stored.
Possible causes
- Damaged fuel pressure sensor
- Poor contact or wiring fault at the fuel pressure sensor
What you can do
- 1Read and note the code, clear it and road test to see whether it returns
- 2Check the fuel pressure sensor connector for oxidation and loose connections
- 3If you have a diagnostic tool: read the fuel pressure sensor value in live data at engine start and at switch-off, and see whether it reaches a reasonable level
- 4Have a workshop with diagnostic equipment check the sensor's voltage supply and replace the sensor if needed
Symptoms you may notice2
- A message appears in the display
- Poor performance, the car lacks power
What the fault can affect1
- The control module uses a calculated fuel pressure instead
General guidance for car owners. Diagnosis on the car can point to a different cause.