VOLVO
ECM-2540 - Fuel system. Pressure too high
System
Engine Control Module (ECM)
Volvo models this fault code applies to
This fault code has different meanings depending on model, model year or engine. Select the meaning that applies to your car.
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
In certain warm-engine operating modes, fuel pressure is controlled by the fuel flow control valve. If the pressure is too high in such a mode, the code is set. The fault can lie in the sensor, in the valve's voltage supply or in the valve itself.
Possible causes
- Damaged fuel pressure sensor
- Fuel flow control valve has no voltage supply
- Damaged fuel flow control valve
What you can do
- 1Read and note the code, clear it and road test to see whether it returns
- 2Check the fuel pressure sensor connector for oxidation, contact resistance and loose connections
- 3Make sure the connector to the fuel flow control valve is clean and firmly attached
- 4Use a multimeter to check that the voltage supply cable to the valve has no open circuit
- 5Have a workshop with diagnostic equipment check the fuel flow control valve and the fuel pressure sensor, and replace them if needed
Symptoms you may notice1
- A message appears in the display
What the fault can affect1
- A calculated value is used instead
General guidance for car owners. Diagnosis on the car can point to a different cause.