VOLVO
ECM-274D - Engine coolant temperature (ECT) sensor. Signal too low
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (24)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo S80 (1999–2006)2006Engine B5204T5, B5254T2 only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2006–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
The engine control module (ECM) works out the engine temperature after start, taking into account time since start, engine speed and load. If the sensor signal is below the calculated temperature, the code is set.
Possible causes
- Contact resistance and oxidation in the connector
- Damaged engine coolant temperature sensor
What you can do
- 1Disconnect the electric cooling fan connector before you begin, so the fan does not start by itself
- 2Check the connector on the temperature sensor for contact resistance and oxidation
- 3Check the coolant level and freeze protection, since a frozen sensor can cause this code
- 4Have a workshop check whether the thermostat opens as it should
- 5Have a workshop replace the coolant temperature sensor if the connector is in good condition and the fault remains
Symptoms you may notice2
- Malfunction indicator lamp (MIL) on
- The engine is hard to start
General guidance for car owners. Diagnosis on the car can point to a different cause.