VOLVO
ECM-280C - Fuel pressure sensor. Signal too high
System
Engine Control Module (ECM)
Volvo models this fault code applies to
This fault code has different meanings depending on model, model year or engine. Select the meaning that applies to your car.
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
The engine control module (ECM) has detected a fuel pressure sensor signal that is higher than it should be. The cause may lie in the sensor, in the wiring to it, or in the connectors.
Possible causes
- Signal cable shorted to ground
- Signal cable shorted to supply voltage
- Open circuit in the signal cable
- Open circuit in the signal ground wire
- Contact resistance, oxide or loose contact in connectors and connections
- Damaged fuel pressure sensor
What you can do
- 1Read the code, clear it and drive until the engine is warm. Then check whether it returns
- 2If you have a diagnostic tool: check in live data whether the fuel pressure sensor value changes with the engine running, or stays constantly high
- 3Check that the connector at the fuel pressure sensor is secure and free from oxide and contact resistance
- 4With the car switched off, use a multimeter to check that the signal wire has no contact with ground or supply voltage and is not broken
- 5Check the ground wire to the sensor for an open circuit
- 6If no damage or connector fault is visible, have a workshop try a new fuel pressure sensor
Symptoms you may notice5
- Engine lacks power when moving off from standstill
- Engine hesitates, surges or runs unevenly under acceleration
- Engine hesitates or surges when slowing down
- Engine is hard to start, cranks slowly or does not start
- Check engine lamp (Malfunction Indicator Light) comes on or behaves abnormally
General guidance for car owners. Diagnosis on the car can point to a different cause.