VOLVO
ECM-2850 - Heated oxygen sensor (HO2S). Signal too low
System
Engine Control Module (ECM)
Volvo models this fault code applies to
This fault code has different meanings depending on model, model year or engine. Select the meaning that applies to your car.
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The engine control module uses the signal from the oxygen sensor to judge the fuel and air mixture. The code is stored when the control module finds that the sensor signal is wrong, in this case too low. The cause may be an open supply or a short circuit in the signal cable.
Possible causes
- Open circuit in the supply voltage to the sensor
- Damaged oxygen sensor
- Signal cable shorted to ground
- Signal cable shorted to supply voltage
What you can do
- 1Switch off the ignition and check the oxygen sensor connector: look for play, oxidation and damage
- 2Check the insulation of the signal cable for chafing and pinching, especially where it runs close to hot parts
- 3With the ignition on, use a multimeter to check that the supply voltage to the sensor is not interrupted
- 4If you have a diagnostic tool: check whether the oxygen sensor value in live data changes while driving. A value that stays still or looks wrong suggests the signal is not correct
- 5If the wiring is in order but the fault remains, have a workshop check the sensor with diagnostic equipment
Symptoms you may notice1
- Message in the information display
What the fault can affect1
- The last measured value from the sensor is used
General guidance for car owners. Diagnosis on the car can point to a different cause.