VOLVO
ECM-2870 - Heated oxygen sensor (HO2S). Signal too low
System
Engine Control Module (ECM)
Volvo models this fault code applies to
This fault code has different meanings depending on model, model year or engine. Select the meaning that applies to your car.
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The control module checks the calibration signal from the oxygen sensor. The code is set when that signal is found to be incorrect, here too low, and a short to ground in the signal cable or a damaged sensor can cause it.
Possible causes
- Signal cable shorted to ground
- Damaged heated oxygen sensor
What you can do
- 1Switch off the ignition and check that the oxygen sensor connector is secure and undamaged
- 2With the car switched off, use a multimeter to check that the signal cable is not in contact with ground
- 3Look for chafing and pinching on the signal cable, especially where it could touch the body
- 4If the cable is intact but the fault remains, have a workshop check the sensor and the control with diagnostic equipment
Symptoms you may notice1
- Message in the information display
What the fault can affect1
- The control module uses the last value it measured from the sensor
General guidance for car owners. Diagnosis on the car can point to a different cause.