VOLVO
ECM-28E0 - Heated oxygen sensor (HO2S). Signal too low
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The engine control module takes its fuel and air mixture information from the oxygen sensor. The code is set when the signal for oxygen content is judged incorrect, here too low. The fault is detected while the engine runs under light load. The cause may be a short to ground in the signal wire, a damaged sensor or a fault inside the control module.
Possible causes
- Signal wire shorted to ground
- Oxygen sensor damaged
- Control module has an internal fault
What you can do
- 1Read the code, clear it and drive with light load to see whether it returns
- 2Switch off the ignition, loosen the oxygen sensor connector and check it is clean, with no play or oxidation
- 3With the car switched off, use a multimeter to check that the signal wire has no contact with ground
- 4If you have a diagnostic tool: see in live data whether the oxygen sensor value changes while the engine runs under light load
- 5If the connector and wire are intact but the fault remains, have a workshop check the sensor and the control module with diagnostic equipment
Symptoms you may notice1
- Message in the information display
General guidance for car owners. Diagnosis on the car can point to a different cause.