VOLVO
ECM-291C - Fuel pump control module. Signal too high
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
The engine control module (ECM) requests fuel pressure from the fuel pump control module through a pulse width modulated (PWM) signal, and that module then drives the pump to match the request. The code is set when the signal between the two modules is too high. It can only be read while the engine is running.
Possible causes
- Signal wire between the ECM and the fuel pump control module shorted to supply voltage
- Damaged fuel pump control module
- Damaged supply wire to the fuel pump control module
- Poor contact, oxidation or looseness in connectors and joints
- Damaged fuel pump or damaged ground connection to the pump
What you can do
- 1Find out whether the fault is permanent or intermittent; if the engine runs normally now, the fault is likely temporary
- 2Inspect the plugs at the fuel pump control module for oxidation and poor contact
- 3Check the power feed to the fuel pump control module and the pump itself, including the relay and fuse
- 4Check the ground connection to the pump control module and the fuel pump
- 5Read the codes in the central electronic module, as this code is often a knock-on effect of electrical faults, and check the signal wire with diagnostic equipment
Symptoms you may notice5
- The engine does not start even though the starter motor turns
- The engine stalls
- Lack of power and poor performance, especially when starting off
- Jerky running, hesitation or surging on acceleration or deceleration
- Engine warning lamp (Check Engine) lit
General guidance for car owners. Diagnosis on the car can point to a different cause.