VOLVO
ECM-2A0D - Fuel temperature sensor. Signal too low
System
Engine Control Module (ECM)
Volvo models this fault code applies to
This fault code has different meanings depending on model, model year or engine. Select the meaning that applies to your car.
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
The engine control module reads the fuel temperature sensor, which is built into the fuel pressure sensor, and the fault is set when that signal is too low. Causes can be poor contact, an open signal or ground wire, a short to supply voltage in the signal wire, or a damaged sensor.
Possible causes
- Contact resistance or oxide in the terminals
- Signal cable shorted to supply voltage
- Open circuit in the signal cable
- Open circuit in the signal ground wire
- Damaged fuel temperature sensor
What you can do
- 1Start the engine and let it warm up. Read the code and see whether it returns
- 2With a diagnostic tool, check the fuel temperature in live data with the ignition on; a value that is too low or still points to the sensor or wiring
- 3Check the connector at the fuel pressure sensor, which also carries the temperature sensor: it should be secure and clean
- 4With the car switched off, use a multimeter to check that the signal and ground wires are not broken and that the signal wire has no contact with voltage
- 5If the wiring is in order but the fault remains, have a workshop check the fuel pressure sensor as needed
Symptoms you may notice1
- No noticeable symptoms for the driver
General guidance for car owners. Diagnosis on the car can point to a different cause.