VOLVO
ECM-2A50 - Pressure sensor particulate trap. Faulty signal
System
Engine Control Module (ECM)
Volvo models this fault code applies to
This fault code has different meanings depending on model, model year or engine. Select the meaning that applies to your car.
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The engine control module (ECM) has registered that the signal from the particulate trap pressure sensor is faulty. The fault can be caused by clogged or swapped hoses, a damaged sensor, or poor contact in the sensor connector.
Possible causes
- Clogged hoses to the particulate trap pressure sensor
- Hoses to the pressure sensor have been swapped
- Damaged pressure sensor
- Contact resistance or oxidation in the connector
What you can do
- 1Make sure the hoses to the sensor are routed correctly and not blocked
- 2Clear the fault code and road test to see whether it returns
- 3If you have a diagnostic tool: read the pressure sensor value in live data with ignition on and then at idle, and compare it with what you expect
- 4Check the connector at the pressure sensor for loose contact, contact resistance and oxidation
- 5If the fault remains after these checks, the sensor may be damaged, and a workshop should check it and reset the adaptation
Symptoms you may notice1
- Poor performance
What the fault can affect1
- Engine output and engine speed are limited
General guidance for car owners. Diagnosis on the car can point to a different cause.