VOLVO
ECM-2AA0 - Particulate filter temperature sensor. Faulty signal
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The ECM keeps watch on exhaust gas temperature. The fault code is set when the signal from the temperature sensor upstream of the particulate trap is faulty, which can be caused by a short circuit, an open circuit or poor contact in the sensor wiring, or by a damaged sensor.
Possible causes
- Contact resistance, oxidation or open circuit in the connections
- Signal wire short-circuited to ground
- Damaged temperature sensor for the particulate trap
What you can do
- 1Check the connector at the temperature sensor for loose contact, contact resistance and oxidation
- 2Use a multimeter to check that the signal wire to the sensor has no contact with the body (ground)
- 3Check that the wiring to the sensor has no open circuit, and gently move it while measuring
- 4If you have a diagnostic tool: read the sensor temperature in live data with the engine warm and see whether it differs clearly from what you expect
- 5If the fault remains, have a workshop measure the sensor resistance and check the wiring
Symptoms you may notice1
- A message appears in the information display
What the fault can affect1
- The control module uses a calculated value for the temperature
General guidance for car owners. Diagnosis on the car can point to a different cause.