VOLVO
ECM-2B30 - Particulate trap. Faulty signal
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The engine control module (ECM) monitors the pressure difference before and after the particulate trap. The fault code is set when the signal from the differential pressure sensor is faulty, for example because of swapped or damaged hoses, poor contact or a damaged sensor.
Possible causes
- The hoses to the particulate trap pressure sensor have been swapped
- Damaged connection hose or pipe to the differential pressure sensor
- Contact resistance or oxidation in the connector
- Open circuit in the signal wire
- Damaged differential pressure sensor
What you can do
- 1Check the hoses and pipes to the differential pressure sensor for damage and leaks
- 2Check that the hoses are not swapped with each other
- 3Check the connector at the differential pressure sensor for contact resistance and oxidation, and make sure it is secure
- 4If you have a diagnostic tool: read the differential pressure sensor signal in live data and check that it responds when the engine idles
- 5If the fault remains, have a workshop measure the supply voltage to the sensor and check the wiring
Symptoms you may notice1
- A message appears in the information display
General guidance for car owners. Diagnosis on the car can point to a different cause.