VOLVO
ECM-304C - Rear knock sensor (KS). Signal too high
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
Under certain operating conditions the control module monitors the rear knock sensor signal. If the signal is too high, the code is stored, and it can be checked while the engine runs. An engine noise or a sensor that has been fitted incorrectly can cause the signal to become too strong.
Possible causes
- Signal wire short-circuited to supply voltage
- Noise from the engine
- Signal wire short-circuited to ground
- Incorrectly installed knock sensor
- Damaged temperature sensor
What you can do
- 1Check that the rear knock sensor is firmly fitted and tightened correctly
- 2Start the engine and listen for noise, since this can cause a signal that is too high
- 3Read and clear the fault code, run the engine and check whether it returns
- 4Follow the signal wire from the rear knock sensor and look for chafing or a short to the battery positive lead
- 5Use a multimeter to check that the ground wire has no contact with supply voltage
- 6Have a workshop check the knock sensor if the fault remains
Symptoms you may notice1
- Poor performance
What the fault can affect2
- Ignition advance is pulled back to protect the engine
- Boost pressure is reduced
General guidance for car owners. Diagnosis on the car can point to a different cause.