VOLVO
ECM-304D - Rear knock sensor (KS). Signal too low
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
Under certain operating conditions the control module monitors the rear knock sensor signal. If the signal is too low, the code is stored, and it can be checked while the engine runs. Poor contact at the sensor connection or a break in the signal wire are the most common causes of a signal that is too weak.
Possible causes
- Contact resistance in the connections to the rear knock sensor
- Open circuit in the signal wire
- Short circuit between the knock sensor signal wires
- Damaged knock sensor
What you can do
- 1Check that the rear knock sensor connector is free from oxidation and firmly seated
- 2Make sure the rear knock sensor is firmly fitted and tightened correctly
- 3Read and clear the fault code, run the engine and check whether it returns
- 4If you have a diagnostic tool, check in live data that the knock signal from the rear sensor changes when the engine is revved
- 5Follow the signal wire from the rear sensor and use a multimeter to check that it is not broken and has no contact with ground
- 6If the fault remains: have a workshop check the knock sensor and its wiring
Symptoms you may notice1
- Poor performance
What the fault can affect2
- Ignition advance is pulled back to protect the engine
- Boost pressure is reduced
General guidance for car owners. Diagnosis on the car can point to a different cause.