VOLVO
ECM-314D - Misfire cylinder 4. Emissions impact
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (22)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2 only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
Misfires on cylinder four during the first revolutions after starting affect the exhaust emissions. The code indicates that cylinder four is the one misfiring, and it can be checked while the engine runs. The causes lie in the fuel system, the intake or the ignition.
Possible causes
- Blocked or leaking injector
- Uneven compression
- Faulty fuel pressure
- Air leakage
- Contaminated or incorrect fuel
- Engine never reaches full operating temperature across repeated cold starts
What you can do
- 1First investigate the other fault codes that affect camshaft control or the camshaft reset valve
- 2Check that the fuel level is adequate and that the engine oil level is correct
- 3Check the crankcase ventilation for blockages
- 4Check the spark plug on cylinder four
- 5Check the intake system for leaks
- 6Have a workshop measure the compression on cylinder four if the other checks show nothing
Symptoms you may notice4
- Engine warning lamp lit
- The engine misfires
- The engine is difficult to start
- Uneven idle
What the fault can affect2
- Rear oxygen sensor control is switched off
- Lambda control is switched off
General guidance for car owners. Diagnosis on the car can point to a different cause.