VOLVO
ECM-330B - Engine speed (RPM) sensor. Signal missing
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
The control module treats it as a fault when the signal from the engine speed sensor is missing, or when the speed signal is lower than the one from the camshaft sensor, and sets the code. The cause may be an open or short circuit in the wiring, poor contact, or a damaged sensor or trigger plate.
Possible causes
- Open circuit in the signal or ground wire
- Signal wire short-circuited to ground or supply voltage
- Contact resistance in the connections
- Damaged engine speed sensor
- Damaged carrier plate
What you can do
- 1Check that the speed sensor connector is firmly seated and free from oxidation
- 2Check the signal wire for open circuit and for short circuit to ground and supply voltage
- 3Check the carrier plate for damage
- 4If you have a diagnostic tool, read the fault status with the engine running and see whether the fault is active
- 5If the fault remains, have a workshop replace the engine speed sensor
Symptoms you may notice2
- The engine does not start
- The engine stops
What the fault can affect1
- The control module uses the camshaft position sensor signal if the camshaft position sensor has been adapted
General guidance for car owners. Diagnosis on the car can point to a different cause.