VOLVO
ECM-341B - Camshaft position (CMP) sensor, exhaust. Signal missing
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
The exhaust side camshaft position sensor occasionally gives no signal, although the signal then returns. The control module treats this as a fault and sets the code. The engine may be hard to start.
Possible causes
- Camshaft position sensor in the wrong position
- Damaged camshaft position sensor
- Loose connection
- Camshafts incorrectly adjusted
What you can do
- 1Start the engine, raise the speed a few times, then read the code
- 2Check that the exhaust camshaft sensor connector is fastened and free from oxidation
- 3Check that the sensor is correctly fitted and not damaged around its housing
- 4If you have a diagnostic tool: read the fault status; "Fault found" means a permanent fault, "No fault found" means it is not active at the moment
- 5Have a workshop check the camshaft angle against the crankshaft with diagnostic equipment
Symptoms you may notice1
- The engine is difficult to start
General guidance for car owners. Diagnosis on the car can point to a different cause.